四川圓管輸送機的結構

核心提示：四川圓管輸送機設備輸送帶的結構：

四川圓管輸送機的結構

四川圓管輸送機設備輸送帶的結構：

圓管帶式輸送機的輸送帶與普通輸送帶的材料結構基本相同，根據不同的承載能力可以選用聚酯棉帆布帶或鋼絲繩芯帶等。圓管帶的芯層結構與普通帶式輸送機輸送帶相比有一定的差別，由于圓管帶式輸送帶在運送物料時需形成管狀，要求輸送帶有良好的彈性、縱向柔性、橫向剛性及抗疲勞性能，同時對輸送帶的芯層材料要求較高，輸送帶搭接部分要有良好的可撓曲性，邊緣芯層設計較薄，以保證輸送帶在形成管狀后的密封和穩定性，保證設備在空載運行工況下不易產生扭轉；同時輸送帶兩邊緣向里側卷曲，有助于形成管狀。

  由于圓管帶式輸送機為曲線設置，為維持管狀，需要輸送帶根據設備的布置情況具有一定的橫向剛度，即在曲線段抵抗輸送帶的張力使其圓形發生改變的能力。圓管帶式輸送機的張力、水平轉彎角度越大，需要圓管帶的橫向剛度就越大。圓管輸送帶的剛度是圓管帶式輸送機設計計算的基礎，也是圓管帶式輸送機同傳統帶式輸送機最本質的區別 。

根據圓管輸送帶剛度值的大小指標，圓管輸送帶一般分為標準剛性帶、高剛性帶、高斷面保持型輸送帶三種類型。其中標準剛性圓管輸送帶剛度最小，高斷面保持型圓管輸送帶剛度最大。高剛性圓管輸送帶比標準剛性圓管輸送帶剛度值高30%左右，而高斷面保持型圓管輸送帶的剛度值更高。圓管輸送帶剛度值定義為：將其縱向裁剪成75mm寬后，放在剛度實驗儀上測得的數值。表8-4為標準剛性圓管輸送帶的剛度數值。